Shipping class: Oversized (No NDA)

  • C6527-01-0010

    C6527-01-0010

    Overview

    C6527-01-0010 is a DPF + DOC used in the diesel particulate filter section of the exhaust aftertreatment system. It is designed for KOMATSU engines and supports soot capture and particulate matter control in heavy duty service. Komatsu builds heavy equipment powered by diesel engines for construction, mining, and industrial uses.

    What this part does

    This diesel particulate filter captures soot from the exhaust stream and stores particulate matter in the filter substrate. During regeneration events the stored soot is burned off, which helps keep backpressure under control and protects components downstream in the system.

    Where this part fits

    This part is generally used on KOMATSU engine platforms installed in class 8 trucks and heavy equipment. Exact fitment depends on the specific engine family, emission level, and chassis configuration.

    Installation and replacement notes

    • Confirm compatibility with the engine family and emission certification level before ordering.
    • Inspect related components for damage or contamination that may have contributed to the original failure.
    • Follow OEM torque specifications and service procedures during installation.
    • When replacing a DPF it is good practice to inspect the diesel oxidation catalyst, check differential pressure readings, verify that active and passive regeneration are working correctly, and correct any root causes of soot overload.

    Specifications

    • Part type: DPF + DOC
    • OEM or application group: KOMATSU

    Related components

    During service you may also need clamps, gaskets, sensors, mounting hardware, or additional aftertreatment components depending on the specific installation.

  • 23075959

    23075959

    Overview

    23075959 is a Gasket used in the exhaust and aftertreatment sealing system. It is designed for engines and supports sealing joints between exhaust and aftertreatment components in heavy duty service.

    What this part does

    This gasket provides a gas tight seal between exhaust and aftertreatment components. Good sealing helps maintain exhaust flow, protect sensors, and avoid soot streaking at joints.

    Where this part fits

    This part is generally used on engine platforms installed in class 8 trucks and heavy equipment. Exact fitment depends on the specific engine family, emission level, and chassis configuration.

    Installation and replacement notes

    • Confirm compatibility with the engine family and emission certification level before ordering.
    • Inspect related components for damage or contamination that may have contributed to the original failure.
    • Follow OEM torque specifications and service procedures during installation.
    • Gaskets should usually be replaced any time a joint is opened. Clean the sealing surfaces and align the gasket carefully before final tightening.

    Specifications

    • Part type: Gasket

    Related components

    During service you may also need clamps, gaskets, sensors, mounting hardware, or additional aftertreatment components depending on the specific installation.

  • 21212522

    21212522

    Overview

    21212522 is a Gasket used in the exhaust and aftertreatment sealing system. It is designed for VOLVO engines and supports sealing joints between exhaust and aftertreatment components in heavy duty service. Volvo supplies heavy duty diesel engines for class 8 highway tractors and vocational trucks.

    What this part does

    This gasket provides a gas tight seal between exhaust and aftertreatment components. Good sealing helps maintain exhaust flow, protect sensors, and avoid soot streaking at joints.

    Where this part fits

    This part is generally used on VOLVO engine platforms installed in class 8 trucks and heavy equipment. Exact fitment depends on the specific engine family, emission level, and chassis configuration.

    OEM and cross references

    This part may replace or cross reference the following numbers:

    • 2013

    Installation and replacement notes

    • Confirm compatibility with the engine family and emission certification level before ordering.
    • Inspect related components for damage or contamination that may have contributed to the original failure.
    • Follow OEM torque specifications and service procedures during installation.
    • Gaskets should usually be replaced any time a joint is opened. Clean the sealing surfaces and align the gasket carefully before final tightening.

    Specifications

    • Part type: Gasket
    • OEM or application group: VOLVO
    • Additional cross references are listed in the section above.

    Related components

    During service you may also need clamps, gaskets, sensors, mounting hardware, or additional aftertreatment components depending on the specific installation.

  • 21371339

    21371339

    Overview

    21371339 is a Gasket used in the exhaust and aftertreatment sealing system. It is designed for CUMMINS engines and supports sealing joints between exhaust and aftertreatment components in heavy duty service. Cummins produces heavy duty diesel engines widely used in class 8 highway tractors and vocational trucks.

    What this part does

    This gasket provides a gas tight seal between exhaust and aftertreatment components. Good sealing helps maintain exhaust flow, protect sensors, and avoid soot streaking at joints.

    Where this part fits

    This part is generally used on CUMMINS engine platforms installed in class 8 trucks and heavy equipment. Exact fitment depends on the specific engine family, emission level, and chassis configuration.

    Installation and replacement notes

    • Confirm compatibility with the engine family and emission certification level before ordering.
    • Inspect related components for damage or contamination that may have contributed to the original failure.
    • Follow OEM torque specifications and service procedures during installation.
    • Gaskets should usually be replaced any time a joint is opened. Clean the sealing surfaces and align the gasket carefully before final tightening.

    Specifications

    • Part type: Gasket
    • OEM or application group: CUMMINS

    Related components

    During service you may also need clamps, gaskets, sensors, mounting hardware, or additional aftertreatment components depending on the specific installation.

  • 21424458

    21424458

    Overview

    21424458 is a Gasket used in the exhaust and aftertreatment sealing system. It is designed for engines and supports sealing joints between exhaust and aftertreatment components in heavy duty service.

    What this part does

    This gasket provides a gas tight seal between exhaust and aftertreatment components. Good sealing helps maintain exhaust flow, protect sensors, and avoid soot streaking at joints.

    Where this part fits

    This part is generally used on engine platforms installed in class 8 trucks and heavy equipment. Exact fitment depends on the specific engine family, emission level, and chassis configuration.

    Installation and replacement notes

    • Confirm compatibility with the engine family and emission certification level before ordering.
    • Inspect related components for damage or contamination that may have contributed to the original failure.
    • Follow OEM torque specifications and service procedures during installation.
    • Gaskets should usually be replaced any time a joint is opened. Clean the sealing surfaces and align the gasket carefully before final tightening.

    Specifications

    • Part type: Gasket

    Related components

    During service you may also need clamps, gaskets, sensors, mounting hardware, or additional aftertreatment components depending on the specific installation.

  • 5417860

    5417860

    Overview

    5417860 is a Gasket used in the exhaust and aftertreatment sealing system. It is designed for CUMMINS engines and supports sealing joints between exhaust and aftertreatment components in heavy duty service. Cummins produces heavy duty diesel engines widely used in class 8 highway tractors and vocational trucks.

    What this part does

    This gasket provides a gas tight seal between exhaust and aftertreatment components. Good sealing helps maintain exhaust flow, protect sensors, and avoid soot streaking at joints.

    Where this part fits

    This part is generally used on CUMMINS engine platforms installed in class 8 trucks and heavy equipment. Exact fitment depends on the specific engine family, emission level, and chassis configuration.

    OEM and cross references

    This part may replace or cross reference the following numbers:

    • 2019

    Installation and replacement notes

    • Confirm compatibility with the engine family and emission certification level before ordering.
    • Inspect related components for damage or contamination that may have contributed to the original failure.
    • Follow OEM torque specifications and service procedures during installation.
    • Gaskets should usually be replaced any time a joint is opened. Clean the sealing surfaces and align the gasket carefully before final tightening.

    Specifications

    • Part type: Gasket
    • OEM or application group: CUMMINS
    • Additional cross references are listed in the section above.

    Related components

    During service you may also need clamps, gaskets, sensors, mounting hardware, or additional aftertreatment components depending on the specific installation.

  • 5304868

    5304868

    Overview

    5304868 is a Gasket used in the exhaust and aftertreatment sealing system. It is designed for CUMMINS/PACCAR engines and supports sealing joints between exhaust and aftertreatment components in heavy duty service. Cummins produces heavy duty diesel engines widely used in class 8 highway tractors and vocational trucks. Paccar engines power many Kenworth and Peterbilt class 8 trucks in long haul and regional haul service.

    What this part does

    This gasket provides a gas tight seal between exhaust and aftertreatment components. Good sealing helps maintain exhaust flow, protect sensors, and avoid soot streaking at joints.

    Where this part fits

    This part is generally used on CUMMINS/PACCAR engine platforms installed in class 8 trucks and heavy equipment. Exact fitment depends on the specific engine family, emission level, and chassis configuration.

    OEM and cross references

    This part may replace or cross reference the following numbers:

    • 2020

    Installation and replacement notes

    • Confirm compatibility with the engine family and emission certification level before ordering.
    • Inspect related components for damage or contamination that may have contributed to the original failure.
    • Follow OEM torque specifications and service procedures during installation.
    • Gaskets should usually be replaced any time a joint is opened. Clean the sealing surfaces and align the gasket carefully before final tightening.

    Specifications

    • Part type: Gasket
    • OEM or application group: CUMMINS/PACCAR
    • Additional cross references are listed in the section above.

    Related components

    During service you may also need clamps, gaskets, sensors, mounting hardware, or additional aftertreatment components depending on the specific installation.

  • 2866337

    2866337

    Overview

    2866337 is a Gasket used in the exhaust and aftertreatment sealing system. It is designed for CUMMINS engines and supports sealing joints between exhaust and aftertreatment components in heavy duty service. Cummins produces heavy duty diesel engines widely used in class 8 highway tractors and vocational trucks.

    What this part does

    This gasket provides a gas tight seal between exhaust and aftertreatment components. Good sealing helps maintain exhaust flow, protect sensors, and avoid soot streaking at joints.

    Where this part fits

    This part is generally used on CUMMINS engine platforms installed in class 8 trucks and heavy equipment. Exact fitment depends on the specific engine family, emission level, and chassis configuration.

    Installation and replacement notes

    • Confirm compatibility with the engine family and emission certification level before ordering.
    • Inspect related components for damage or contamination that may have contributed to the original failure.
    • Follow OEM torque specifications and service procedures during installation.
    • Gaskets should usually be replaced any time a joint is opened. Clean the sealing surfaces and align the gasket carefully before final tightening.

    Specifications

    • Part type: Gasket
    • OEM or application group: CUMMINS

    Related components

    During service you may also need clamps, gaskets, sensors, mounting hardware, or additional aftertreatment components depending on the specific installation.

  • 21592961

    21592961

    Overview

    21592961 is a Combustion Chamber used in the aftertreatment regeneration system. It is designed for VOLVO/MACK engines and supports controlled fuel combustion to generate heat for DPF regeneration in heavy duty service. Volvo supplies heavy duty diesel engines for class 8 highway tractors and vocational trucks. Mack produces heavy duty engines and trucks for construction, refuse, and highway applications in the class 8 segment.

    What this part does

    This combustion chamber is used to burn injected fuel and generate the heat required for active regeneration of the diesel particulate filter.

    Where this part fits

    This part is generally used on VOLVO/MACK engine platforms installed in class 8 trucks and heavy equipment. Exact fitment depends on the specific engine family, emission level, and chassis configuration.

    Installation and replacement notes

    • Confirm compatibility with the engine family and emission certification level before ordering.
    • Inspect related components for damage or contamination that may have contributed to the original failure.
    • Follow OEM torque specifications and service procedures during installation.
    • Inspect fuel lines, igniters, and temperature sensors when servicing the combustion chamber and correct any root cause that led to improper regeneration.

    Specifications

    • Part type: Combustion Chamber
    • OEM or application group: VOLVO/MACK

    Related components

    During service you may also need clamps, gaskets, sensors, mounting hardware, or additional aftertreatment components depending on the specific installation.

  • 20992179

    20992179

    Overview

    20992179 is a Combustion Chamber used in the aftertreatment regeneration system. It is designed for VOLVO/MACK engines and supports controlled fuel combustion to generate heat for DPF regeneration in heavy duty service. Volvo supplies heavy duty diesel engines for class 8 highway tractors and vocational trucks. Mack produces heavy duty engines and trucks for construction, refuse, and highway applications in the class 8 segment.

    What this part does

    This combustion chamber is used to burn injected fuel and generate the heat required for active regeneration of the diesel particulate filter.

    Where this part fits

    This part is generally used on VOLVO/MACK engine platforms installed in class 8 trucks and heavy equipment. Exact fitment depends on the specific engine family, emission level, and chassis configuration.

    Installation and replacement notes

    • Confirm compatibility with the engine family and emission certification level before ordering.
    • Inspect related components for damage or contamination that may have contributed to the original failure.
    • Follow OEM torque specifications and service procedures during installation.
    • Inspect fuel lines, igniters, and temperature sensors when servicing the combustion chamber and correct any root cause that led to improper regeneration.

    Specifications

    • Part type: Combustion Chamber
    • OEM or application group: VOLVO/MACK

    Related components

    During service you may also need clamps, gaskets, sensors, mounting hardware, or additional aftertreatment components depending on the specific installation.

  • 21771038

    21771038

    Overview

    21771038 is a Combustion Chamber used in the aftertreatment regeneration system. It is designed for VOLVO/MACK engines and supports controlled fuel combustion to generate heat for DPF regeneration in heavy duty service. Volvo supplies heavy duty diesel engines for class 8 highway tractors and vocational trucks. Mack produces heavy duty engines and trucks for construction, refuse, and highway applications in the class 8 segment.

    What this part does

    This combustion chamber is used to burn injected fuel and generate the heat required for active regeneration of the diesel particulate filter.

    Where this part fits

    This part is generally used on VOLVO/MACK engine platforms installed in class 8 trucks and heavy equipment. Exact fitment depends on the specific engine family, emission level, and chassis configuration.

    Installation and replacement notes

    • Confirm compatibility with the engine family and emission certification level before ordering.
    • Inspect related components for damage or contamination that may have contributed to the original failure.
    • Follow OEM torque specifications and service procedures during installation.
    • Inspect fuel lines, igniters, and temperature sensors when servicing the combustion chamber and correct any root cause that led to improper regeneration.

    Specifications

    • Part type: Combustion Chamber
    • OEM or application group: VOLVO/MACK

    Related components

    During service you may also need clamps, gaskets, sensors, mounting hardware, or additional aftertreatment components depending on the specific installation.

  • 21771033

    21771033

    Overview

    21771033 is a Combustion Chamber used in the aftertreatment regeneration system. It is designed for VOLVO/MACK engines and supports controlled fuel combustion to generate heat for DPF regeneration in heavy duty service. Volvo supplies heavy duty diesel engines for class 8 highway tractors and vocational trucks. Mack produces heavy duty engines and trucks for construction, refuse, and highway applications in the class 8 segment.

    What this part does

    This combustion chamber is used to burn injected fuel and generate the heat required for active regeneration of the diesel particulate filter.

    Where this part fits

    This part is generally used on VOLVO/MACK engine platforms installed in class 8 trucks and heavy equipment. Exact fitment depends on the specific engine family, emission level, and chassis configuration.

    Installation and replacement notes

    • Confirm compatibility with the engine family and emission certification level before ordering.
    • Inspect related components for damage or contamination that may have contributed to the original failure.
    • Follow OEM torque specifications and service procedures during installation.
    • Inspect fuel lines, igniters, and temperature sensors when servicing the combustion chamber and correct any root cause that led to improper regeneration.

    Specifications

    • Part type: Combustion Chamber
    • OEM or application group: VOLVO/MACK

    Related components

    During service you may also need clamps, gaskets, sensors, mounting hardware, or additional aftertreatment components depending on the specific installation.